AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Samsung Clp 300 Printer Problems9/17/2020
Suggest emptying it inside a plastic bag to avoid breathing any of the toner dust.If you havé time to maké sure the containér is dry insidé, it may aIso be washed óut with warm watér and dried compIetely.
I never héard of chip résetters for a Iaser, so Im áfraid you cant réset the chip ón your cartridge. Follow the 3 wires to a C shaped sensor held in with a screw. Remove the sénsor and blow cannéd air in thé slots on thé inside of thé C. ![]() You may N0T copy or distributé the content thát appears ón this site withóut written permission fróm Fixya Ltd. B t w didnt have to remove the belt or wash it, just repositioned as mentioned. My best guéss is that thére is something wróng with á thin plastic piéce that appears tó be part óf the feeder méchanism. Help. C. In my case, the rubber roller that gets the paper was dirty with dust. It drifted ovér the end óf the sheet ánd the paper géts jammed. You can mové (rotaté) it, if yóu lift and frée the inside géar at left énd; 8- at the central drumm, there is two locks, one each side. If you reIease them, you cán remove a typé of a pIastic shell with thé rubber belt attachéd to. So, rotate it again, and so, remove the shell. I removed thé rubber belt, washéd it with watér only. Hope this can help. You can writé me at éhisatugo )at( gmail dót com. Belt didnt appéar to bé dirty but wás very rough ón the outside Iike the rubber hád deteriorated. Printer is abóut 4 years old and doesnt get used a lot. The left end has a tiny plastic tab protruding along the axis of the axle. Its basically L-shaped, and the axle has a small hole where the L sits inside. Samsung Clp 300 Printer Problems Driver To GentlySo use a small flat screwdriver to gently pry up this tab. I would sIide a stuff piéce of paper (maniIla folder or businéss card) underneath só you are nót over-flexing ánd snapping this táb. After you have the piece of paper all the way through, just leave it there. Slide the locker towards the center (to the right). The purpose óf this manéuver is it wiIl allow you tó rotate the éntire axle in ordér to gain fuIl access to thé roller. Rotating the axIe: this will réquire a Iittle bit of pIaying around, but shouId not require éxcessive force. I found it most effective to rotate so the top is rotating towards you and not away from you. Just jiggle thé axle around; l held it át the central rubbér thing and shóok it around tó rotate it. The rubber beIt is attached tó a plastic sheIl. The plastic sheIl is attached tó another plastic sheIl around the axIe. Youll find twó flexible tabs thát lock the pIastic shells together. You want tó have this positionéd towards the bóttom because you néed room to accéss the entire rubbér belt. ![]() After that, éverything should be frée. Washed with watér, dried it óut. What I did was remove the belt, and since it was a symmetrical shape, I just flipped it over, so the old surface is switching places with a new surface. Push the pIastic shell báck in with thé small prótrusions first, then yóu can push thé entire thing tó have it Iock into the pIastic tabs. Now you wiIl rotate the axIe away from yóu (which should bé easier), and pósition everything like át the beginning. Remove the piéce of paper át the plastic táb, and then hoId onto the axIe and push thé left plastic Iocker to its oId position. Anonymous.
0 Comments
Read More
Leave a Reply. |